MotorClaw.news
Subscribe
Search releases, companies, topics...
Updated

ZF's High Revolution Drive spins to 30,000 rpm to shrink the electric motor, with production targeted for 2030

ZF has built a 3-in-1 electric drive that revs to 30,000 rpm, letting it shrink the motor by nearly 25 percent while delivering the same power.

Maximum motor speed
30,000 rpm
Peak output (version shown)
200 kW
Peak wheel torque (version shown)
3,500 Nm
Reduction in required magnet mass
50 percent

What Happened

ZF has developed the High Revolution Drive, a compact 3-in-1 electric drive that spins at up to 30,000 rpm, making it smaller and lighter than conventional drives while delivering the same power. The concept builds on ZF's existing SELECT platform, so automakers can bring it into new vehicles faster and at lower development cost. ZF is focusing on the high-volume passenger car market, with drive outputs of approximately 150 to 200 kW. The company says it is already in talks with several automakers and is targeting production by 2030.

Maximum motor speed

30,000rpm

ZF calls this speed the economic and technical sweet spot for the configuration presented.

The principle behind the drive is that, at the same power output, a higher rotational speed reduces the required motor torque. Since torque is closely linked to rotor volume, the electric motor can be designed smaller and lighter. To turn that speed into usable torque, a two-stage spur gear transmission with a ratio of about 18:1 delivers the required torque to the wheels. The version shown delivers peak output of 200 kW and peak wheel torque of 3,500 Nm.

High Revolution Drive (30,000 rpm) vs. comparable SELECT drive (18,000 rpm)
Installation size
Nearly 25 percent smaller
Weight
Nearly 25 percent lighter
Required magnet mass
Reduced by 50 percent
What ZF says the drive offers
  • Up to 30,000 rpm with low noise
  • Efficiency of nearly 93 percent, on par with the comparable SELECT system
  • Lower weight that helps increase electric range
  • Scalable architecture for different power ratings
  • Compatibility with both 400- and 800-volt platforms
  • Built as a variant of the modular SELECT platform using existing technologies
“Robustness and low noise and vibration levels were stringent development targets from the outset. To achieve this, we considered the electric motor, gearing, bearings and tooth geometry as an integrated system. For the configuration presented, 30,000 rpm is the economic and technical sweet spot.”
— Thomas Meiser, Head of the E-Mobility Business Unit at ZF

Higher speeds make noise and vibration harder to control, and ZF says it addresses this with decades of gear and transmission experience. Meiser describes the drive as drawing on ZF's full systems expertise, with the electric motor, power electronics and transmission coordinated systematically rather than optimized in isolation. The reduced magnet mass also lowers costs and reduces dependence on critical supply chains. ZF says the drive's predictable product costs and production flexibility come from reusing its modular system instead of starting from scratch for every new drive variant.

Why this matters

Because a smaller, lighter motor needs half the magnet mass, the drive could cut costs and reduce automakers' exposure to critical supply chains, while lighter hardware helps extend electric range for buyers. ZF says it is already in talks with several automakers and is aiming for production by 2030, with the focus on the high-volume passenger car market.

Terms in This Story

3-in-1 electric drive
An electric drive that combines the motor, power electronics and transmission into a single integrated unit rather than separate parts.
rpm
Revolutions per minute, the measure of how fast a motor's rotor spins.
rotor
The rotating part inside an electric motor; its volume is tied to how much torque the motor can produce.
spur gear
A simple toothed gear with straight teeth that transmits power between parallel shafts, often used in multi-stage transmissions.
Read Original: ZF

Summarised from the linked release; details can be imperfect — always verify against the original source.

How useful was this article?

Feedback goes to the MotorClaw Desk and does not subscribe you to email. Privacy.